Connect to your VPS: SSH with PowerShell or PuTTY
How to log in to your server from Windows via SSH, with PowerShell or PuTTY, and what to do if your password is not accepted.
You manage your server over SSH: an encrypted connection where you type commands as if you were sitting right in front of it. On Windows this works without extra software in PowerShell, or with the well-known program PuTTY.
What you need
In your customer area under Server management → Access → Credentials you find:
- IP: your server's address, e.g.
10.0.0.25 - User: usually
root - Password: the password for this user
The server has to be running. You can see its state at the top of the server page.
Option 1: PowerShell (Windows 10 and 11)
- Press the Windows key, type
PowerShelland open it. - Enter the following, replacing the address with your server's IP:
ssh root@10.0.0.25
- On the first connection Windows asks whether you trust the server (
Are you sure you want to continue connecting). Typeyesand press Enter. - The server now asks for the password (
root@10.0.0.25's password:). Enter the password and press Enter.
Important: while you type the password nothing appears: no dots, no asterisks, the cursor does not move. That is intended on Linux. Just keep typing and press Enter.
To paste in PowerShell, right-click (Ctrl+V does not work in older windows).
You are in when you see a line like root@your-server:~#. Type exit to disconnect.
Option 2: PuTTY
- Download PuTTY from the official site putty.org and install it.
- Start PuTTY. Enter your server's IP under Host Name (or IP address). Port stays
22, Connection type staysSSH. - Optional: enter a name under Saved Sessions and click Save, so you do not have to type the address again next time.
- Click Open.
- The first time, a security alert about the server's key appears. Click Accept.
- At
login as:typerootand press Enter. - Then enter the password and press Enter. Here, too, nothing appears while you type.
Pasting in PuTTY also works with a right-click. Selected text is copied automatically.
Password not accepted?
This is the most common case. Go through these points in order:
- Copy instead of typing. Copy the password from the customer area and paste it with a right-click. Make sure you do not copy a space at the start or end. Then press Enter, even though you see nothing.
- Check upper and lower case, Caps Lock and your keyboard layout (German vs. English swaps
yandz, for example). - Use the user
root, not your email address or customer area username. Those are two different logins. - Is password login enabled? Under Access there is the switch Password login (SSH). If it is off, the server only accepts SSH keys. Turn it on if you want to log in with a password.
- Set a new password. Under Settings → Reset root password you set a new password. This works even if SSH is not reachable right now.
- After a reinstall a new password applies. Windows may also warn that the server's key has changed (
REMOTE HOST IDENTIFICATION HAS CHANGED). That is normal after a reinstall. Remove the old entry in PowerShell withssh-keygen -R 10.0.0.25(your IP) and connect again. In PuTTY, confirm the warning with Accept.
No connection at all?
If you are not even asked for the password (Connection timed out or Connection refused):
- Is the server running? Start it in the customer area.
- Is the IP correct?
- Did you add rules in your server's firewall that block port 22?
- Use our free port check to see whether port 22 is reachable.
The console in your browser
Under Console → Open console you see your server's screen right in the browser, even if network or SSH are down. Keep in mind:
- Pasting does not work. The console only transmits key presses, your clipboard does not reach it. You have to type the password by hand.
- Our generated password is long and contains characters like
+,/and=as well as easily confused letters (l,I,O,0). Typos happen quickly, and if the keyboard layout does not match, special characters arrive wrong. - Easiest way: under Settings → Reset root password set your own password that you can type reliably (at least 8 characters, longer is better). Use it to log in to the console as
root. After that, connect via SSH as described above, where pasting works.
Even safer: SSH keys
Instead of a password you can log in with an SSH key. You add it to the server under Access. See Create an SSH key and turn off password login. After that you can turn off password login, so nobody can try out passwords anymore.
If you are still stuck, open a ticket with a screenshot of the error message.
For the community
Know your stuff? Write a guide.
Share what you know: we review every submitted guide, publish it under your name and say thank you with credit for your services.